Port LOGGING - DLT-VERBOSE 🛈¶
Access to DLT verbose messages
Stimulation¶
This port has no stimulus capabilities.
Properties 🛈¶
Name |
Available if |
Default value |
Valid values |
Type |
Description |
|---|---|---|---|---|---|
Active mode |
☑ |
bool |
When this option is selected, ecu.test actively connects to the site. If the setting is not selected, ecu.test does not establish a Connection itself. Rather, only data addressed to another tool is read (passive mode). |
||
DLT TCP auto reconnect timeout [sec] |
Active mode: ‘True’ |
float |
ecu.test will automatically restart the DLT TCP connection if no new DLT messages arrive within the configured number of seconds. An empty value for the timeout switches the auto reconnect feature off. |
||
Pre-recording circular buffer |
Active mode: ‘True’ |
0 |
int |
Since the recording gets started only a short time after the connection to the ecu is established, even with auto-start/stop, messages sent by the ECU only once immediately after the connection is made, can be lost. With this setting, the recording can be “extended forward” by the specified number of messages, in order to include these initial messages. |
|
Network name |
string |
Name of the network as defined in SIL-Kit Config yaml. |
|||
Controller name |
string |
Name of the controller as defined in SIL-Kit Config yaml. |
|||
MAC address ❲client❳ |
Active mode: ‘True’ |
‘02:00:4C:4F:4F:50’ |
string |
String (format: 02:00:4C:4F:4F:50), ‘default’ if the adapter MAC address should be used |
|
IP version |
Active mode: ‘True’ |
IPv4 |
[IPv4, IPv6] |
string |
Selection of the IP version used |
My own IP address |
Active mode: ‘True’ |
string |
IP address to be used as a client. It must be located in the same subnet as the IP address of the device under test, and must not be equal to the IP address of another participant. |
||
Gateway address |
Active mode: ‘True’ |
string |
IP address, leave empty if no gateway is needed |
||
Subnet mask / prefix length |
Active mode: ‘True’ |
‘default’ |
string |
For IPv4 addresses a subnet mask or prefix length can be given (format: ‘255.255.255.0’ or ‘24’). ‘default’ uses the default subnet mask of the network class of IP address (client). For IPv6 only a prefix length is accepted and the value ‘default’ is not supported. |
|
VLAN settings |
‘no tagging’ |
[‘no tagging’, ‘single tagging’] |
string |
Used VLAN setting |
|
VLAN-VID |
1 |
int |
Integer, only used if VLAN tagging is enabled |
||
Logger protocol |
Active mode: ‘False’ |
[, PLP/TECMP, ASAM CMP] |
string |
Use a logger protocol such as ASAM CMP. The port can then only be used for reading. Ethernet frames contained in the logger messages are extracted and the filter in BPF format (if specified) is applied to these frames. |
|
Device and Stream IDs |
Active mode: ‘False’ » Logger protocol: ‘ASAM CMP’ |
string |
Identifiers of the devices and streams as a list of tuples, each consisting of device ID and stream ID, e.g.: (1,2),(3,4). Leave empty if no filtering based on device and stream ID is needed. |
||
Interface IDs |
Active mode: ‘False’ » Logger protocol: ‘ASAM CMP’ |
string |
Identifiers of the interfaces: empty if no filtering based on interface IDs is required; several can be separated by commas. |
Jobs 🛈¶
Reconnect¶
In Active Mode, reconnects and clears the message buffers.
Parameterization
Return value
Name |
Available if |
Default value |
Valid values |
Type |
Description |
|---|---|---|---|---|---|
result |
False |
[False, True] |
bool |
Returns True if the connection was successfully established |