Port BUSACCESS - CAPTURE-LIN¶

Capture access to LIN

This port requires a PCAP driver to be installed.

Stimulation¶

This port has no stimulus capabilities.

Name	Available if	Default value	Valid values	Type	Description
Network interface card			[ONLINE]	string	Used network interface card
Logger protocol		PLP/TECMP	[PLP/TECMP, ASAM CMP]	string	Which logger protocol is used.
Do not stop RBS		☐		bool	Restbus simulation stays active beyond test case execution.
Probe ID / Device ID	Logger protocol: ‘PLP/TECMP’	0		int	Identifier of the probe / device
Bus Spec ID / Interface ID	Logger protocol: ‘PLP/TECMP’	0		int	Identifier of the bus specification / interface
Device-ID and Stream-ID	Logger protocol: ‘ASAM CMP’	‘(0,0)’		string	Tuple consisting of device ID and stream ID, e.g.: (0,0)
Interface-ID	Logger protocol: ‘ASAM CMP’	0		int	Identifier of the interface
LIN version		‘1.3’	[‘1.3’, ‘2.0’]	string	LIN protocol version to be used. Only affects calculation and validation of the frame checksum. 1.3 = received frames must have a classic checksum. 2.0 = received frames may have enhanced or classic checksum. If the database does not define a checksum mode for a specific frame to be sent, this option will be taken into account to use either classic (1.3) or enhanced (2.0) checksum mode.
Bus-DB				string

Erases the receiving buffer of given frame

Parameter

Name	Available if	Default value	Valid values	Type	Description
FrameId				int	Frame ID

Return value

Name	Available if	Default value	Valid values	Type	Description
result				ByteStream	ByteStream

Ungeristers a frame that is being streamed to an inbox

Parameter

Name	Available if	Default value	Valid values	Type	Description
FrameId				int	Frame ID
Inbox				object	Existing inbox

Parameter

Name	Default value	Valid values	Type	Description
FrameName			string	Frame name
NodeName			string	Name of the electronic control unit
RawValue	False	[False, True]	bool	If ‘True’, the Raw value is returned.
Reset	False	[False, True]	bool	If ‘True’ the first received value will be deleted after it has been read
SignalName			string	Signal name

Registers the frame for use with other jobs

Parameter

Name	Available if	Default value	Valid values	Type	Description
FrameId				int	Frame ID

Reads the given frame ID (use InitLinFrame before!)

Parameter

Name	Available if	Default value	Valid values	Type	Description
doDelete		False	[False, True]	bool	Deletes the Frame after reading if “True”
FrameId				int	Frame ID

Return value

Name	Available if	Default value	Valid values	Type	Description
result				ByteStream	ByteStream

Reads the given frame ID (use InitLinFrame before!)

Parameter

Name	Available if	Default value	Valid values	Type	Description
doDelete		False	[False, True]	bool	Deletes the Frame after reading if “True”
FrameId				int	Frame ID

Return value

Name	Available if	Default value	Valid values	Type	Description
result				object	LinFrame

Registers a frame to be streamed to an inbox.

Parameter

Name	Default value	Valid values	Type	Description
FrameId			int	Frame ID
Inbox			object	Existing inbox
saveAsLinFrame	False	[False, True]	bool	If True, the frame is saved as a LinFrame object, else as a ByteStream

Erases the first received value of the given signal

Parameter

Name	Type	Description
FrameName	string	Frame name
NodeName	string	Name of the electronic control unit
SignalName	string	Signal name

All in one: Set data, temporarily enable a frame, and send a master request. Frame ID must be registered in advance via the job “InitFrame”.

Parameter

Name	Default value	Valid values	Type	Description
checkSumMode	‘Default’	[‘Enhanced’, ‘Classic’, ‘Default’]	string	Mode of the checksum calculation. With default the LIN version from the TBC is used for the determination.
DataByteStream			ByteStream	data to be send
FrameId			int	Frame ID